GCODE

Bed Level Probe

;Generated with Cura_SteamEngine 5.0.0
M140 S60
M105
M190 S60
M104 S215
M105
M109 S215
G29; auto home
G92 E0 ; reset extruder
; done purging extruder
G1 Z1.0 F3000 ; move z up little to prevent scratching of surface
M117 peter solomon design
; FIRST PASS
G0 Z10 F7200 ; Raise nozzle
G0 X30 Y35 Z10 ; Go to pos above 1st location
G0 X30 Y35 Z0 ; Go to 1st location
M117 First Corner 1st Round ; displays status
G4 S8 ; Wait 8 seconds
G0 Z10 ; Raise nozzle
G0 X30 Y205 Z10 ; Go to pos above 2nd location
G0 X30 Y205 Z0 ; Go to 2nd location
M117 Second Corner 1st Round ; displays status
G4 S8 ; Wait 8 seconds
G0 Z10 ; Raise nozzle
G0 X200 Y205 Z10 ; Go to pos above 3rd location
G0 X200 Y205 Z0 ; Go to 3rd location
M117 Third Corner 1st Round ; displays status
G4 S8 ; Wait 8 seconds
G0 Z10 ; Raise nozzle
G0 X200 Y35 Z10 ; Go to pos above 4th location
G0 X200 Y35 Z0 ; Go to 4th location
M117 Fourth Corner 1st Round ; displays status
G4 S8 ; Wait 8 seconds
G0 Z10 ; Raise nozzle
G0 X115 Y118 Z10 ; Go to pos above middle
G0 X115 Y118 Z0 ; Go to middle
M117 Middle 1st Round ; displays status
G4 S5 ; Wait 5 seconds
; SECOND PASS
G0 Z10 F7200 ; Raise nozzle
G0 X30 Y35 Z10 ; Go to pos above 1st location
G0 X30 Y35 Z0 ; Go to 1st location
M117 First Corner 2nd Round ; displays status
G4 S6 ; Wait 6 seconds
G0 Z10 ; Raise nozzle
G0 X30 Y205 Z10 ; Go to pos above 2nd location
G0 X30 Y205 Z0 ; Go to 2nd location
M117 Second Corner 2nd Round ; displays status
G4 S6 ; Wait 6 seconds
G0 Z10 ; Raise nozzle
G0 X200 Y205 Z10 ; Go to pos above 3rd location
G0 X200 Y205 Z0 ; Go to 3rd location
M117 Third Corner 2nd Round ; displays status
G4 S6 ; Wait 6 seconds
G0 Z10 ; Raise nozzle
G0 X200 Y35 Z10 ; Go to pos above 4th location
G0 X200 Y35 Z0 ; Go to 4th location
M117 Fourth Corner 2nd Round ; displays status
G4 S6 ; Wait 6 seconds
G0 Z10 ; Raise nozzle
G0 X115 Y118 Z10 ; Go to pos above middle
G0 X115 Y118 Z0 ; Go to middle
M117 Middle 2nd Round ; displays status
G4 S5 ; Wait 5 seconds
; THIRD PASS
G0 Z10 F7200 ; Raise nozzle
G0 X30 Y35 Z10 ; Go to pos above 1st location
G0 X30 Y35 Z0 ; Go to 1st location
M117 First Corner 3rd Round ; displays status
G4 S4 ; Wait 4 seconds
G0 Z10 ; Raise nozzle
G0 X30 Y205 Z10 ; Go to pos above 2nd location
G0 X30 Y205 Z0 ; Go to 2nd location
M117 Second Corner 3rd Round ; displays status
G4 S4 ; Wait 4 seconds
G0 Z10 ; Raise nozzle
G0 X205 Y205 Z10 ; Go to pos above 3rd location
G0 X205 Y205 Z0 ; Go to 3rd location
M117 Third Corner 3rd Round ; displays status
G4 S4 ; Wait 4 seconds
G0 Z10 ; Raise nozzle
G0 X200 Y35 Z10 ; Go to pos above 4th location
G0 X200 Y35 Z0 ; Go to 4th location
M117 Fourth Corner 3rd Round ; displays status
G4 S4 ; Wait 4 seconds
G0 Z10 ; Raise nozzle
G0 X115 Y118 Z10 ; Go to pos above middle
G0 X115 Y118 Z0 ; Go to middle
M117 Middle 3rd Round ; displays status
G4 S4 ; Wait 4 seconds
; FOURTH PASS
G0 Z10 F7200 ; Raise nozzle
G0 X30 Y35 Z10 ; Go to pos above 1st location
G0 X30 Y35 Z0 ; Go to 1st location
M117 First Corner 4th Round ; displays status
G4 S3 ; Wait 3 seconds
G0 Z10 ; Raise nozzle
G0 X30 Y205 Z10 ; Go to pos above 2nd location
G0 X30 Y205 Z0 ; Go to 2nd location
M117 Second Corner 4th Round ; displays status
G4 S3 ; Wait 3 seconds
G0 Z10 ; Raise nozzle
G0 X200 Y205 Z10 ; Go to pos above 3rd location
G0 X200 Y205 Z0 ; Go to 3rd location
M117 Third Corner 4th Round ; displays status
G4 S2 ; Wait 2 seconds
G0 Z10 ; Raise nozzle
G0 X200 Y35 Z10 ; Go to pos above 4th location
G0 X200 Y35 Z0 ; Go to 4th location
M117 Fourth Corner 4th Round ; displays status
G4 S3 ; Wait 3 seconds
G0 Z10 ; Raise nozzle
G0 X115 Y118 Z10 ; Go to pos above middle
G0 X115 Y118 Z0 ; Go to middle
M117 Middle 4th Round ; displays status
G4 S3 ; Wait 3 seconds
G0 Z30 ; Raise nozzle
M117 Done Leveling ; displays status
; BEGIN DISPLAYLAYERPROGRESS SETTINGS
; DisplayLayerProgress_layerIndicatorProcessed = true
; END DISPLAYLAYERPROGRESS SETTINGS
; BEGIN DISPLAYLAYERPROGRESS SETTINGS
; DisplayLayerProgress_layerIndicatorProcessed = true
; END DISPLAYLAYERPROGRESS SETTINGS

Must-Know Commands

M503 – Displays printer settings

M500 – Save to EEPROM

M503 Settings 6.4.2023

Recv: echo:; Linear Units:
Recv: echo:  G21 ; (mm)
Recv: echo:; Temperature Units:
Recv: echo:  M149 C ; Units in Celsius
Recv: echo:; Filament settings (Disabled):
Recv: echo:  M200 S0 D1.75
Recv: echo:; Steps per unit:
Recv: echo:  M92 X79.90 Y79.60 Z406.60 E429.19
Recv: echo:; Max feedrates (units/s):
Recv: echo:  M203 X500.00 Y500.00 Z10.00 E60.00
Recv: echo:; Max Acceleration (units/s2):
Recv: echo:  M201 X500.00 Y500.00 Z100.00 E250.00
Recv: echo:; Acceleration (units/s2) (P<print-accel> R<retract-accel> T<travel-accel>):
Recv: echo:  M204 P1000.00 R1000.00 T1000.00
Recv: echo:; Advanced (B<min_segment_time_us> S<min_feedrate> T<min_travel_feedrate> X<max_jerk> Y<max_jerk> Z<max_jerk> E<max_jerk>):
Recv: echo:  M205 B20000.00 S0.00 T0.00 X8.00 Y8.00 Z0.40 E5.00
Recv: echo:; Home offset:
Recv: echo:  M206 X0.00 Y0.00 Z0.00
Recv: echo:; Auto Bed Leveling:
Recv: echo:  M420 S1 Z10.00 ; Leveling ON
Recv: echo:  G29 W I0 J0 Z0.35937
Recv: echo:  G29 W I1 J0 Z0.19705
Recv: echo:  G29 W I2 J0 Z-0.06119
Recv: echo:  G29 W I0 J1 Z0.16015
Recv: echo:  G29 W I1 J1 Z0.04210
Recv: echo:  G29 W I2 J1 Z-0.20138
Recv: echo:  G29 W I0 J2 Z0.04210
Recv: echo:  G29 W I1 J2 Z0.09621
Recv: echo:  G29 W I2 J2 Z0.07407
Recv: echo:; Material heatup parameters:
Recv: echo:  M145 S0 H185.00 B45.00 F255
Recv: echo:  M145 S1 H240.00 B70.00 F255
Recv: echo:; Hotend PID:
Recv: echo:  M301 P16.28 I1.68 D39.39
Recv: echo:; Bed PID:
Recv: echo:  M304 P462.10 I85.47 D624.59
Recv: echo:; Power-loss recovery:
Recv: echo:  M413 S0 ; OFF
Recv: echo:; Z-Probe Offset:
Recv: echo:  M851 X-31.94 Y-40.66 Z-1.80 ; (mm)
Recv: echo:; Input Shaping:
Recv: echo:  M593 X F40.00 D0.15
Recv: echo:  M593 Y F40.00 D0.15
Recv: echo:; Linear Advance:
Recv: echo:  M900 K0.22
Recv: ok P15 B3